Otherwise, assemble cannot be accomplished. Remove the Cap. Foldable Glass 2. Remove 2 screws of the Shelf Folderble Glass Shelf. Before disassembling the Water Tube, take out the compressor cover. Pull the two hose out from the water valve. Lose the hooks by pushing the flat-blade driver. Cut the sponge stick on the Case Water tank. Remove the 2 screws under the. Motor Damper 2. Disengage 2 housing connector. Turn the water filter count-clockwise. Refer to the picture 2. Remove the water filter by pulling it.
Refer to the picture Water Filter 3. Remove 2 screw cap parts with a flat-blade - screwdriver. Remove the angle cap with a flat-blade screwdriver. Pull the drawer open to full extension. Press the both side hooks with flat-blade - screwdriver. Refer to picture Freezer Door 7. Remove the Freezer Rail by pulling it. Unscrew 4 bolts. Lifting up the convertible door. Flex Zone Light 2. Disengage the housing. Separate the Side lamp from the Refrigerator Light case.
Remove the freezer door and freezer drawer by pulling out the drawer and then unscrewing 2 screws. Evaporator Cover 2. Unscrew 6 screws of cover compressor. Remove 1 screw and disengae the housing connector. Refer to the picture 3. Unscrew 1 screw fixed on left. Step Valve 2. Disengage the housing connector. Disengage all housing connectors from the main PCB. Self-diagnostic function 1 Self-diagnostic function in the Initial power ON Micom operates self-diagnostic function to check the temperature sensor condition within 1 second when the refrigerator turned On initially.
This function is for changing the standard temperature. If the trouble is detected by self-diagnosis - The error of sensor will be displayed on the front of display. Connector CN31 inserted Temperature table correctly? If door is opened and closed once at a high ambient temperature, it will be operated after 1 minute delay. If Ice Maker does not operate 1.
Power is applied to the one end of wires. Be careful when disassembling and shall refer to its exploded diagram in any case. Please take care of yourself during repair and measurement. Check after 7 minutes Does compressor Refer to test function work with manual in the manual operation? Did buzzer of manual operation sound? Check certainly after manual operation Is freezer sensor normal?
Remove causes after comprehending the conditions of interferance by door gasket, food etc, Is water penetrated into the door switch? If buzzer does not sound even though the button is pressed, manual operation is started and door is opened, it should separate panel PCB and check the breakage of buzzer and bad soldering. If ICE Water is not supplied 1. Disconnect the housing connector. Remove 2 hex head bolts from sides with a socket wrench 10mm 5.
Take out the upper drawer by lifting it up. Remove the tilting pocket 1 by pulling both support guards 2 aside.
And take out both support guards by pulling them aside. Re-attach the lower left and right door hinges Insert the screw 10 into the lower left and right door hinges, then tighten with a Philips head screwdriver. Page 14 4. Connect the dispenser door tube 5 and, then insert a clip on the coupler while pulling tube. Connect the connector 4 on the left side door and one connector 3 on the right side door. The clip is enveloped inside of the top cap. Pull out the rails fully on each side of the cabinet.
Attach the Flex door front onto the open slots on the sides. Tighten 2 hex head bolts completely with a socket wrench 10mm. Page Assemble The Freezer Drawer 6. Insert the upper drawer. Remove 2 pieces of tape 4 attached to the side of the drawer bin. Reattach the tape in the same position when moving the refrigerator to prevent scratching the drawer bin. Page Adjusting The Level Make sure the refrigerator is level so that you can make final adjustments.
Use a level to test if the refigerator is level both side to side and back to front. If the refrigerator is not level, it will not be possible to get the doors perfectly even, which may cause moisture condensation and increased energy bills.
If you need help, review the previous section on leveling the refrigerator. The left door is fixed. To make minor adjustments between doors, adjust only the right door. Locate the height-adjuster 1 in the freezer drawer. Unscrew the 8 Phillips screws 2 slightly to loosen the door. If the refrigerator is installed in an area with low water pressure below 20psi , you can install a booster pump to compensate for the low pressure.
Page Installing The Water Line 6. After you turn on the refrigerator, let the ice maker make ice for 1 to 2 days. Over that period of time, throw out the first 1 or 2 buckets of ice the freezer makes to ensure all impurities have been removed from the water line.
Page Completing The Set Up SEt uP Now that you have your new refrigerator installed in place, you are ready to set up and enjoy the features and functions of the appliance. By completing the following steps, your refrigerator should be fully operational.
The beeping stops when you close the door. The door alarm function is pre-set to On in the factory. Power Cool is useful if you need to quickly cool items or need to cool the refrigerator rapidly if it has warmed dramatically for example, if the door was left open.
The Filter light turns red to let you know when it is time to change your water filter cartridge. Page 26 For a replacement water filter, you can visit your local home Improvement center or contact the Samsung Parts distributor.
Once the normal set temperatures are reached, the blinking will stop. If the blinking continues for a long period of time, please contact a Samsung Electronics Service Center.
Dispense 4 to 6 ice cubes into the glass. After 8, and then 16 hours, dispense a full glass of ice. When the chime sounds, release the Test button. Page 29 - It may cause injury. Do not try to disassemble the ice maker. Do not wash or spray the ice bucket with water while it is in the refrigerator. Remove it to clean it. Water clouding phenomenon All water provided to the refrigerator flows through the core filter which is an alkaline water filter.
In the Here are some of the customized compartments we have created to keep your food fresher longer. To more thoroughly prevent odor from seeping into the ice compartment, wrap stored food securely and make food containers as airtight as possible. Initially, the Cold Drinks mode is selected.
The refrigerator will adjust the temperature in the Flex Zone automatically to the temperature you selected.
0コメント